How to Clean Your Bissell CleanView Vacuum After Using It

This post contains affiliate links. As an Amazon Associate, we earn from qualifying purchases.

To clean a Bissell CleanView vacuum after use, empty the dirt tank, remove and wash the pre-motor foam filter and cyclone with warm water and mild detergent, let them air dry for a full 24 hours, and check the brush roll for tangles. Never operate the vacuum with damp filters or without all filters in place, as this can damage the motor.

That 24-hour dry window isn’t a suggestion. It’s printed in the manual for the CleanView 3533 and 3536 because the foam holds water longer than you think. Put a damp filter back in, and you’re pulling moist air through the motor on the next run. The smell tells you first, a faint, musty odor that means the paper in the post-motor filter is already wicking moisture.

What follows is the sequence that actually matches the manufacturer’s specs: which parts you wash, which you only tap clean, and the one mistake that voids the two-year warranty on the spot.

Key Takeaways

  • The pre-motor foam filter and plastic cyclone are washable with warm, soapy water but require a full 24 hours to air dry completely.
  • The post-motor filter is not washable for most CleanView models; only tap it clean and replace it when dirty.
  • Never run the vacuum with damp filters or with any filter missing. This forces the motor to pull in unfiltered, moist air, leading to immediate loss of suction and long-term damage.
  • Commercial use voids the manufacturer’s warranty on household models like the 3533 and 3536.
  • A clogged or tangled brush roll is a primary cause of suction problems and poor pickup; clear it every few uses.

The 5-Step Post-Use Cleaning Sequence

Follow this order after every major cleaning session or when you notice a drop in power. Skipping steps forces the motor to work harder, and you’ll hear the pitch change within a few minutes.

Before you start: Unplug the vacuum. This isn’t just a safety line, the brush roll can engage if the power switch is on, and the motor can start if the tank release button is pressed. A plugged-in vacuum with the tank off is live.

  1. Empty the Dirt Tank. Press the tank release button on the vacuum body and pull the tank straight out. Hold it over a trash can, press the bottom release latch, and let the debris fall. Give the tank a light tap to dislodge fine dust. If you’ve vacuumed up fine powder or pet hair, rinse the tank with water and dry it thoroughly.
  2. Remove and Clean the Cyclone. Twist the plastic cyclone unit counter-clockwise and pull it down from the tank. Rinse it under warm running water. Use a drop of mild dish soap and your fingers to scrub off the dust film clinging to the inside vanes. Rinse until the water runs clear. > This is the technical step most guides gloss over. The cyclone creates a vortex that separates heavy debris from the air stream. A layer of dust on the vanes breaks the vortex, sending more fine particles directly into the filter and clogging it faster.
  3. Remove and Wash the Pre-Motor Foam Filter. Lift the release latch on the dirt tank lid to access the filter compartment. Pull out the blue or gray foam filter. Hand-wash it in warm water with a small amount of mild detergent. Squeeze it gently, don’t twist or wring it, until the water runs clear. This filter catches the largest debris before air reaches the motor.
  4. Dry the Washable Parts for 24 Hours. Place the cyclone and the foam filter on a clean towel in a well-ventilated area. They must air dry for a full 24 hours before reinstalling. Do not use heat from a hair dryer or radiator, as it can warp the plastic or degrade the foam.
  5. Check and Clear the Brush Roll. Tilt the vacuum back. Look at the rotating brush roll at the base of the power foot. Use a seam ripper, utility knife, or scissors to cut away any wound-up hair, string, or carpet fibers. Pull the debris out from both ends. Spin the brush roll by hand to ensure it moves freely.
Step Component Key Action Risk If Skipped
1 Dirt Tank Empty & tap clean Reduces capacity, fine dust recirculates
2 Cyclone Wash with soap & water Fine dust bypasses, clogs filter in 2-3 uses
3 Pre-Motor Filter Hand wash, no twisting Motor draws in debris, fails within months
4 All Washable Parts Air dry 24 hours Moisture damages motor, creates mildew smell
5 Brush Roll Cut away tangles Poor pickup, overheats belt, burns out motor

TL;DR: Tank, cyclone, foam filter, dry, brush roll. That order matters because a clean cyclone protects a clean filter.

What Most People Get Wrong About the Filters

The CleanView uses a two-stage filtration system. Confusing them is how a simple cleaning creates a new problem.

The pre-motor foam filter sits in the dirt tank lid. It’s a thick, spongy rectangle. This is your washable workhorse. Its job is to catch dirt that gets past the cyclone before that dirt reaches the motor fan. Wash it monthly under warm water.

The post-motor filter is usually a pleated paper or felt cartridge located near the exhaust grill. For most CleanView models, this filter is not washable. Getting it wet ruins its ability to trap microscopic dust. When this filter is dirty, you tap it gently over a trash can to dislodge loose dust and replace it every 3 to 6 months.

Common mistake: Washing the post-motor filter. Water damages the paper media, collapsing the pleats. The vacuum will then expel a fine dust cloud into your room, and the motor will overheat trying to push air through the clog.

Here is the core maintenance schedule drawn from the manufacturer’s guidance for general CleanView/PowerClean models:

Filter Type Cleaning Method Frequency Replacement Cadence
Pre-Motor (Foam) Hand wash, air dry After heavy use / Monthly 6–12 months (if torn)
Post-Motor (Paper/Felt) Tap clean only Monthly Every 3–6 months
Cyclone Wash with soapy water Monthly Only if damaged

If you experience a sudden loss of suction, the first move is always a complete filter check. A clogged post-motor filter is a frequent culprit for general vacuum suction issues.

The Brush Roll & Belt: Your Vacuum’s Engine

Suction pulls dirt in, but the brush roll beats it loose. When this system fails, the vacuum glides over dirt.

After unplugging the machine, tilt it back to inspect the brush roll. Look for: * Hair and thread wound around the ends. * Carpet fibers wrapped around the central cylinder. * A brush roll that doesn’t spin freely by hand.

Cut the debris away with a sharp tool. Pull the strands out from the sides. For a deep clean, some models allow you to remove the brush roll cover. The Model 4438 manual notes it’s secured with seven #2 Phillips head screws. If the cover is broken or the roll is damaged, replace the entire assembly.

A worn drive belt will also stop the brush from spinning. If the roll is clear but the motor hums without movement, the belt is likely stretched or broken. Consult a guide for specific brush roll issues on your model.

Where this goes sideways: Letting hair build up on the brush roll ends. The friction creates enough heat to melt the nylon bristle strips right off the roller. You’ll find little melted plastic beads on the brush roll after a few months of neglect.

The One Rule That Voids Your Warranty

The user manual for CleanView models 3533 and 3536 includes a clear, all-caps warning: “THIS MODEL IS FOR HOUSEHOLD USE ONLY. COMMERCIAL USE OF THIS MACHINE VOIDS THE MANUFACTURER’S WARRANTY.”

This isn’t corporate fine print. It’s a durability rating. Household motors are engineered for 30- to 60-minute run times with cool-down periods. Running the vacuum for hours in a commercial setting, like a small office or a rental property turnover, overheats the motor. The thermal protector will trip repeatedly, and the windings will eventually fail.

The warranty is a two-year limited guarantee. Voiding it means a burnt-out motor is a full replacement cost, not a free repair.

How This Compares to Other Bissell Cleaners

Comparing dry vacuum filter maintenance to wet carpet cleaner brush roll cleaning. The post-use logic is similar across Bissell’s lineup, but the components differ. Knowing what you’re dealing with saves time.

  • Bissell CrossWave: This is a wet/dry vacuum and mop. Post-use cleaning is mandatory to prevent mildew. You must rinse the dirty water tank, wash the dual-action brush roll, and clean the suction channel immediately.
  • Bissell Featherweight: As a lightweight stick vacuum, maintenance is simpler. It often has a single, washable filter behind the dirt cup. Dry it completely.
  • Bissell SpotClean Pro: This is a portable carpet cleaner. The critical steps are emptying the dirty water tank, rinsing the hose and tool, and running clean water through the suction path to clear detergent residue.
  • Bissell Little Green: Similar to the SpotClean Pro, the focus is on preventing mildew in the fluid tanks and hoses. A vinegar rinse every few uses is standard.
  • Bissell TurboClean Pro & PowerClean Pro: These are full-size carpet cleaners. The post-use drill involves cleaning the solution and recovery tanks, the brush roll, and the hoses to avoid clogs and odors.

The Bissell CleanView is simpler by design, a dry vacuum with a focus on air path maintenance. Its complexity is in the filter system, not fluid management.

Frequently Asked Questions

Can I use my Bissell CleanView on wet surfaces?

No. The manual explicitly states “Do not use outdoors or on wet surfaces.” These are dry vacuums. Water can cause an electrical short, damage the motor, and instantly ruin the paper post-motor filter. For wet pickup, you need a Bissell CrossWave or a dedicated wet/dry shop vacuum.

What should I do if my vacuum still has weak suction after cleaning?

Follow a systematic check. First, ensure all filters are completely dry and correctly seated. Second, check for a clog in the hose, wand, or air path. Third, inspect the brush roll for obstructions. If these are clear, you may have a more serious suction problem like a worn belt, a leak in the air system, or a failing motor.

How often should I replace the filters?

Replace the washable pre-motor foam filter if it becomes torn or fails to spring back after washing. Replace the non-washable post-motor filter every 3 to 6 months under normal use, or sooner if you have pets or allergies. The official guidance for models like the 4438 states filters should be replaced every 6 months.

Is the post-motor filter really not washable?

For the vast majority of CleanView models, yes, it is not washable. The material is a pleated paper or a synthetic felt designed to trap fine particles. Water destroys the paper’s structure and clogs the felt. When in doubt, check your specific model’s manual. If it doesn’t say “washable,” assume it’s not.

Can I clean the cyclone with vinegar?

You can, but mild dish soap is usually sufficient and less abrasive. If you want to disinfect or remove hard water scale, a rinse with a diluted white vinegar solution (one part vinegar to three parts water) is safe for the plastic. Rinse thoroughly with clean water afterward.

Before You Go

Clean the tank every time. Wash the foam filter and cyclone monthly, and give them a full day to dry. Never run the machine with a damp filter inside. Keep the brush roll free of hair and string. That’s the entire maintenance schedule. It takes 15 minutes of active work and a day of patience.

The alternative is a gradual decline in power, a motor that smells like hot dust, and a warranty that doesn’t cover the repair. The 24-hour dry rule is the line between maintaining an appliance and replacing it.